Your shopping cart is empty!
10148
Brand:
Roks
98.47 грн
Promotions and discounts
Sending parcels at 16.00

Silicon carbide is widely used in a wide variety of fields in various forms (free or bound grains, suspensions in oil, glycerin, ethylene glycol). In machining, it is used for grinding, honing, water jet cutting, sandblasting processes. In powder form, silicon carbide is used primarily for lapping surfaces and is used more widely in this application than any other material. for directing the suspension to the working surfaces of the same bars. Both are done to increase the productivity of the process.
Silicon carbide is very hard (9-9.5 on the Mohs scale). It is an extremely "scratchy" substance that can cut almost anything. At the same time, due to its physical properties, the grain of silicon carbide is destroyed, forming no less abrasively active particles of a smaller size, which continue to work actively.
As an abrasive material, silicon carbide is found mainly in two forms - the so-called. black and green. In their physical, mechanical and chemical properties, they differ slightly, mainly in the amount of impurities, which determines the color. In fact, green silicon carbide has a SiC content of 99.66%, while black has 98.26%. However, the green silicon carbide process is much more energy intensive and expensive. Therefore, in practical applications, as a rule, it is limited to the use of black silicon carbide, unless there are special recommendations.
Alignment of abrasive stones on silicon carbide powder.
Sprinkle on the surface of the glass (glass thickness must be at least 6 mm) a little silicon carbide powder (half a teaspoon is sufficient). Add some water and spread the resulting mixture over the surface of the glass. Unless there are specific instructions from the bar manufacturer that prohibit the use of soapy water*, a little liquid soap can be added to improve process control. On a stone pre-soaked for 10 minutes in water, apply a pencil grid on the side that you will align. Then, with light pressure, drive the stone over the surface of the glass coated with silicon carbide powder in a figure-of-eight motion. In places of abrasion of the pencil grid, you can control the progress of the process. When the pencil grid disappears, the block is leveled. You can apply it as intended or continue the same process with finer silicon carbide powder until you get the desired surface roughness.
* It is absolutely forbidden to use anything other than pure water when leveling or otherwise using SHAPTON stones. This manufacturer prohibits the use of detergents when sharpening, leveling or cleaning stones, since the substances contained in the soap solution destroy the surface of the bars. It is also not recommended to use soap when working with Bakelite bonded abrasives, as they soften in an alkaline environment.

Additional characteristics:

Country of origin Ukraine
Material - Silicon carbide
Consistency - Powder
Size in microns up to/from -3/2 - 200/160 microns
Packing - Glass, plastic bottle
Weight - 100 g.

Reviews: 0

There are no reviews for this product.

Questions: 1
 Сергей
14/01/2023
Подскажите какая зернистость порошка подходит к различным камням разной зернистости? Как это рассчитывается? К примеру какой порошок нужен камню с зернистостью 1000 грит, 3000 грит, 220 грит?
The administration's response:
Стартовая зернистость порошка для выравнивания, выбирается исходя из неровностей на рабочей поверхности камня, которую необходимо устранить. Если дефект геометрии бруска существенный (седло или скол), то для любой гритности камня выравнивание начинается с порошка F80 (200/160мкм). Но в большинстве случаев выравнивание начинают с порошка F150 (100/80мкм). После завершения операции выравнивания на первом порошке, нужно переходить на следующий - примерно в 2 раза меньший по размеру зерна. Например, с порошка 100/80мкм нужно переходить на порошок 50/40мкм либо на порошок 40/28мкм, чтобы убрать царапины на камне от более грубого порошка. Так следует, с уменьшением в 2 раза размера зерна, продолжать притирать камень до порошка, чья зернистость будет в 2 раза больше размера зерна в камне, который выравнивается. Например, если выравнивается камень Boride 1000 грит (средний размер зерна - 4мкм) - его следует финишировать на порошке зернистостью примерно 10/7мкм. Соответствие размера зерна и зернистости для различных систем гритности можно посмотреть на нашем сайте в разделе Полезное/Калькулятор гритности. Грубые обдирочные камни от 100 до 220 грит выравниваются грубым порошком F80 в один подход.

Similar Products